Peakworks
Peakworks D-Ring extender 2 X 18" (46 cm) for safety harness
FPLE
$18.90
Return conditions:
No returnable if used. For more information about our return policy, please refer to the Orders and Returns.
Extender strap for fall protection. This extender is equipped with a ring to hook oneself to an anchor point. Length of 2 in X 18 in / 5 cm X 45.72 cm.
Peakworks product code: V860302 or model CP-14010
According anchorage strap is designed to withstand a tensile strength of 5000 lb (22 kN) which meets CSA Z259.10-06, ANSI Z359.1-2007.
Inspection:
The worker is responsible for visually inspecting his equipment before each use. During this routine inspection, the worker must note any signs of degradation, malfunction, or breakage. The anchor will have to be replaced if any such signs are detected.
On top of this routine inspection, the strap must be inspected by a qualified person different than the worker. The frequency of these inspections varies according to the manufacturer. Some manufacturers require an inspection every 90 days, others every 180 days, or even yearly. These inspections should be performed more often if your equipment is used in extreme environmental working conditions.
Sylprotec offers a fall protection equipment inspection service. Find out more by clicking on the Services tab, under the Sylprotec logo at the top of the page.
Any equipment that has withstood a fall or an impact must be scrapped.
Maintenance:
For cleaning, use a gentle soap or detergent and lukewarm water (37°C). Do not use bleach, chlorine, or other abrasive or chemical products. If your harness is too dirty or contaminated, it is time to replace it.
Air dry without using heat in a clean environment. You can accelerate the drying process by wiping the wet lanyard with a clean absorbent wipe, or by using a fan. Avoid exposure to sunlight and to any sources of contamination.
Suggestion:
To complete your fall protection you will find a range of harness and anchors. Some products are suggested under the "accessories" tab at the bottom of this page.
Other equipment frequently used with this safety harness:
Safety glasses YA12E93101DX
Liberty TA14LR safety helmet and the essential TA14CS chin strap
EPTCONE28 Traffic Cones
Peakworks FPBAG storage bag
The FPL9903 Tool Strap
FPLE
Data sheet
- Type of product
- Safety equipment
- Main category
- Personal protection
- Sub category
- Fall protection
- Sub sub category
- Lanyards
- Name of the product
- Extension for fall protection
- Product code
- FPLE
- Approved/Certified
- Complies with CSA Z259.10-06 and ANSI Z359.1-2007 standards
- Manufacturer
- Peakworks
- Country of origin
- China
- Format
- 2 in X 18 in / 5 cm X 45.72 cm
- Reusable
- Reusable with careful inspection and proper installation
- Features
- Equipped with a small ring to connect the harness to an anchor point
- Characteristic adding safety
- Designed to withstand static forces of 5000 lbs (22 KN)
- Characteristics of metal parts
- Non-painted metal parts
- Property of the material
- Polyester straps offer better resistance to acidic chemicals
- Material1
- Polyester
- Material2
- Steel
- Washable
- Wash in warm water, 98.60°F/ 37°C. Never use bleach or other abrasive or chemical products on your strap. Air dry
- Length (in/cm)
- 6 in / 15.24 cm
- Width (in/cm)
- 6 in / 15.24 cm
- Height (in/cm)
- 1 in / 2.54 cm
- Weight (lb/kg)
- 0.3 lb / 0.1 Kg
- Sold by
- Unit
- Color
- Black/Grey
- Return conditions
- No returnable if used. For more information about our return policy, please refer to the "Orders and Returns" link on the home page
New
8 other products in the same category:
Customers who bought this product also bought:
